Pro Maintenance Kit

€89,95 EUR
€89,95 EUR
Tax included. Shipping calculated at checkout.

In stock, ready to ship

  • Packed and shipped from our workshop in Berlin
  • Shipping cost for your country shown in the cart
Open full size
EU harmonised notice on the legal guarantee of conformity
When a reel runs heavier at the end of the season than at the start, it is rarely broken. It is dirt, old grease and the wrong tools.
Pro Maintenance Kit: tool case, maintenance mat, three greases and cast lube oil
Everything inside the Pro Maintenance Kit
Tool case with pin remover, pick tool, lock nut wrench, screwdriver, hex key, bearing check tool and tweezers
Which grease goes where in a baitcasting reel
Avail maintenance mat, 34 x 48 cm

Pro Maintenance Kit

Pro Maintenance Kit: tool case, maintenance mat, three greases and cast lube oil

When a reel runs heavier at the end of the season than at the start, it is rarely broken. It is dirt, old grease and the wrong tools. This kit is the full service setup: the tools to open the reel, the lubricants for every part inside, and a mat to work on so no screw rolls away. It is the same setup we use on the bench every day.

What is inside

  • Tool case with 7 tools in a foam insert: pin remover, pick tool, lock nut wrench, screwdriver with 7 bits, 2.5 mm hex key, bearing check tool and precision tweezers. Plus a cleaning brush and two small parts boxes for screws and spares.
  • Avail maintenance mat, 34 x 48 cm, made in Japan. Antistatic, heat resistant to 500 °C, non slip silicone, with parts trays and a ruler edge.
  • Deuthlon Starter Kit with four lubricants matched to the job:
    • Semi Fluid Grease for the worm shaft and level wind gears
    • Reel Gear Ceramic for the main gear
    • Power Drag Grease for the drag washers
    • Cast Lube oil for the spool bearings

Tool kit or Pro Kit?

The Baitcaster Reel Tool Kit on its own is 49.95 €. The Pro Kit adds the mat and all four lubricants for 89.95 €. If you only swap spool bearings, the tool kit is enough. If you want to strip, clean and grease the whole reel, take the Pro Kit.

Good to know

  • Works for baitcasters and spinning reels.
  • No step by step manual inside. Every reel is built differently. Our guides show the common jobs.

Pro Kit + spool bearings

Service the reel. Swap the bearings while it is open.

The spool bearings are the part that decides how far you cast. Type your reel below, pick a class, and the matching pair goes in with the Pro Kit. Together the kit costs less.

  1. 1Type your reel
  2. 2Pick Apex, Edge or Core
  3. 3Set and Pro Kit go in together

Your reel

Which spool bearings fit your reel?

Type the model. You get the exact pair for your reel, with our pick marked.

Know your sizes? Shop single bearingsSingle bearings Browse all reelsAll reels

“Thought there was a motor built in, it just does not stop spinning.” Martin, customer of our Berlin workshop

  • 154 reels matched
  • 30-Day Performance Boost Guarantee
  • Ships from our workshop in Berlin

The full service setup

Everything to open, clean and grease a reel.

After a season a reel runs heavier than it should. Old grease, dirt and a bit of water are enough. With the right tools, the right lubricant for each part and a clean place to work, a full service is an evening at the table. This box has all three.

Everything inside the Pro Maintenance Kit Tool case with pin remover, pick tool, lock nut wrench, screwdriver, hex key, bearing check tool and tweezers Which grease goes where in a baitcasting reel Avail maintenance mat, 34 x 48 cm
  • 7 toolsin a hard case with cut foam
  • 34 x 48 cmAvail maintenance mat, made in Japan
  • 3 greasesplus cast lube oil from Deuthlon
  • 1 boxnothing to collect from three shops

Which grease goes where

Four lubricants, four jobs.

One grease for everything is how most reels end up slow. Each part in a reel needs something different, so the kit has one lubricant per job.

  • Semi Fluid Grease

    For the worm shaft and the level wind gears. Soft enough that the line guide keeps running light.

  • Reel Gear Ceramic

    For the main gear, where the load is highest when you crank against a fish.

  • Power Drag Grease

    For the drag washers. Keeps the drag smooth and steady, also on long runs.

  • Cast Lube oil

    For the spool bearings and the spool shaft. Very thin, so the spool keeps its free spin.

  • Avail maintenance mat

    Antistatic, heat resistant to 500 °C, non slip silicone. Parts trays and a ruler edge, so no screw rolls away.

  • Tool case

    Pin remover, pick tool, lock nut wrench, screwdriver with 7 bits, 2.5 mm hex key, bearing check tool and tweezers. Plus a brush and two parts boxes.

Tool kit or Pro Kit?

Pick by the job you plan.

  • Swap spool bearings: Tool Kit, €49,95

    The case with all 7 tools. Enough to open the spool side, change the bearings and close the reel again.

  • Full service: Pro Kit, €89,95

    The same case plus the mat and all four lubricants. For stripping the reel, cleaning out old grease and building it up fresh.

Good to know: there is no manual in the box, because every reel is built differently. Our guides show the common jobs step by step. Maintenance is at your own risk.

FAQ

Questions about the tools

Does my reel need a pin remover?

Only if a spool bearing sits behind a pin on the spool shaft. Type your reel into the bearing finder. It tells you if your reel is one of them.

Is the pin remover part of the tool kit?

Yes. The Baitcaster Reel Tool Kit includes a pin remover. If you only need to get the pin out, the single pin remover is enough.

Baitcaster Reel Tool Kit €49,95
Spool Bearing Pin Remover €24,95
Which reels do the tools fit?

The tools are made for baitcasting reels. Bits, wrench and hex key cover the common screws and handle nuts.

Is there a manual?

No. Every reel comes apart a little differently. If you service your own reels you will know your way around. Maintenance and installation are at your own risk.